DAWSON CZPT & MOULD Group
***EXTRUSION BLOW MOLDING Equipment Expert***
Our customers are all all around the entire world.
Vietnam, Australia, Indonesia, Malaysia, Thailand, Sri Lanka, Kazakhstan, Russia, UAE, Saudi Arabia, Malta, Romania, Italy, India, Syria, Ethiopia, Egypt, Sudan, Tunisia, Algeria, Kenya, Nigeria, South Africa, Zimbabwe, Mexico, Guatemala, Ecuador, Colombia, Venezuela, Peru….
Accumulation variety blow molding machine ABLD100
Appropriate for generating one hundred-250L HDPE Daily life buoy, floater…
Equiped with MOOG parison controller
with SERVO Motor
Extrusion blow molding machine ABLD100
| extruder | |||
| 1 | Screw diameter | 100mm | |
| 2 | L/D ratio | 24:1 | |
| 3 | Screw speed | 15~50r.p.m. | |
| four | Generate motor | 45Kw | |
| five | Heating zone with cooling enthusiast | 6 zone | |
| 6 | Output/Capability | a hundred and seventy Kg/hr(HDPE particle) | |
| 8 | Heating capability | 25.one kw | |
| 9 | Vertical adjustment of head | 500mm | |
| ten | Forward/Backward adjustment of head | 500mm | |
| eleven | Groove feed barrel cylinder | Have IKV | |
| 12 | Equipment box | Challenging gear decelerator | |
| thirteen | Ladder and basic safety rails | Have | |
| Accumulator CZPT | |||
| 1 | Accumulator ability | 20L(15kgHDPE) | |
| two | Design | First in and initial out | |
| three | Heating zone | 6 zone | |
| four | Heating ability | twenty five.1kw | |
| 5 | Max die&pin diameter | 450mm | |
| 6 | Die head axis with pre-blow | Ø120mm | |
| seven | Accumulator drive-out stroke measurement | Transducer Italy Gefran | |
| 8 | Injection strain | twelve Mpa | |
| 9 | Extruder end | Have | |
| CLAMPING Device | |||
| 1 | Tie bar | Two tie bar | |
| two | Platen measurement | 900(W)X1400(H) | |
| three | Length of mold | 900-960mm | |
| four | Clamping power | 780KN | |
| 5 | Shut/Open up stroke | 880-1700mm | |
| 6 | Mold bodyweight | Max. 5000 kg | |
| seven | Clamping stroke measurement | Transducer Italy Gefran | |
| eight | CZPT valve | ZheJiang Hitech | |
| 9 | Variety of hydraulic cylinder | 1 | |
| ten | Higher stress | 14 Mpa | |
| 11 | Help components for platen movement | Liner Xihu (West Lake) Dis. | |
| HYDRAULIC Method | |||
| one | Main motor/vice motor | AC15Kw/15Kw | |
| 2 | CZPT valve | ZheJiang Hitech | |
| 3 | CZPT pump | ZheJiang Hitech | |
| four | Oil tank potential | 850L | |
| 5 | Operating force | 12 Mpa | |
| 6 | Cooling drinking water for oil | set | |
| seven | Manage of oil level | be noticed dipstick | |
| PNEUMATIC Technique | |||
| one | Functioning pressure | .8 Mpa | |
| 2 | Blow strain | .eight Mpa | |
| 3 | Needle blow circuit | High & minimal pressure | |
| four | Intermittent blow | Have | |
| 5 | Controlled support air for parison | Have | |
| 6 | Air Valves | AIRTAC | |
| 7 | Rapid exhaust for assist air | Have | |
| PARISON Handle | |||
| one | Programmer | JAPAN MOOG | |
| 2 | Servo valve | MOOG |
|
| 3 | Servo cylinder | Intergret of die head | |
| four | CZPT pack |
ZheJiang YOSHE Variable Displacement Piston Pumps |
|
| CZPTITY | |||
| 1 | Contactor |
Schneider |
|
| 2 | Whole linked load (approx.) |
114kw/h | |
| 3 | Average strength intake (approx.) |
forty two kw/h | |
| Water COOLING | |||
| one | Machine water consumption |
6000L/h | |
| two | Mould water intake |
6000L/h | |
| AIR Consumption | |||
| 1 | Compressed air usage | 1.2 kgf/cm2, 3000 L/min | |
| OTHER Attributes | |||
| one | PLC handle | MITSUBISHI | |
| 2 | Xihu (West Lake) Dis.n machine interface | Hitech | |
| three | Recipe storage in hard disk | Available | |
| HEATING Manage | |||
| 1 | Power provide to heating factor | Relay + Contactor | Japan Omron+Korea LG |
| 2 | Manage | PLC controle | |
| 3 | Type of thermocouple | K Variety | |
| 4 | Adjustable reduced and upper limit alarm | Have | |
| five | Cold begin avoidance for screw | Have | |
| six | Alarm for thermocouple and heating element breakage | Have, heating component breakage by anperemeter | |
| seven | Pre-heating perform | Have | |
| Die-ring AND Die-pin | |||
| 1 | one particular sets of die & pin | One set according to client | |
| two | Examination content | Consumer provide 300kg materials to vendor for device tests | |
| Selection | |||
| one | Base blow (hydraulic) and sealing unit (pneumatic) | CZPT blow pin (such as expand & up-down & parison seal) | |
| 2 | Robotic | Have | |
| three | Device Dimension | 6.8×3.3×5 | |
| 4 | Total fat | 20 | |
