EP model alternative gearbox for woods rotary gearbox
NEW 40 HP GEARBOX Sleek Enter one 3/8 12 spline output Interchangable with market place well-liked dimension i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous A lot more
Functions
(one) brand name new 45 horse electrical power shearpin gearbox. This gearbox suits numerous different helps make of 4′,5′ and some 6′ rotary cutters. I offer a great deal of these bins each and every yr for many different applications and carry ALL Replacement Areas for this box, but with any luck , you is not going to have to fret about that.
Below are the specs on the box:
*forty five horse power gearbox
*Standard 1-3/8″ sleek enter shaft(exactly where the pto shaft hooks on). The pto shaft is held on by a one/2 shearbolt.
*size of the enter shaft out of the gearbox is 3″ lengthy
*bolt gap sample for mounting is on the corners, 4-three/four center of gap to heart of hole. It normally takes a 5/eight” bolt.
*twelve splined output shaft(exactly where the blade provider hooks up on the bottom)
*1-9/16 outside the house measurement over the output shaft splines- from the foundation of the output cap to the stop of the splines is 2-three/four” lengthy- all round size of the output shaft is four-1/two” extended.
*will take a 1″ threaded castle nut and a carter crucial on the base of the output shaft to protected blade pan(NUT is incorporated – – BLADE PAN IS NOT!!)
*general peak of the box from the leading of the mower deck to the leading of the box is nine-one/2″
This is a fairly weighty item (47 lbs.) so freight is not inexpensive, but we do not make something off of freight, what ever ups costs us we demand you.
40 HP
one:one:47 Ratio
1-three/8″ Easy Enter Shaft with Shear Pin Gap
1-one/2″ 12-Spline Ouput Shaft
Bolt Sample: six-one/2″ (four) 5/eight” Holes, 5″ Centre Hole Required for Shaft Assembly
The Input and Output Shafts Can not be Bought Serparately.
They are Bought as a package.
The package involves the pursuing areas: input shaft, enter equipment, output shaft, output equipment.
The Shaft Package Can’t Be Separated.
EP manufacturer substitution gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or in any other case performing incorrectly? You’ve got appear to the proper spot.
Study under for the most typical problems with rotary cutter gearboxes and their answers (from swift and soiled, to expert).
Leaking Base Seal:
If you have wrapped some baling or fencing wire close to your output shaft and blown the seal, the expert issue to do is to change the seal.
If your output seal is intact, and you are able to get ID, OD and thickness measurements (in millimeters), most bearing residences can buy you up a generic double-lip seal that will get you back again up-and-managing. If not, give us a get in touch with and we can assist you type out what you need to have.
A dental select is the best way to eliminate the previous seal ahead of pressing in the new 1.
If you might be lucky ample to have a slow-leak, the rapid and filthy approach is to operate automotive-kind grease in the gearbox right up until the new seal will come in. Be sure to check out and add grease more frequently than you would with oil, as this is NOT a expert fix.
Damaged Output Shaft:
Uh oh. You hit something that didn’t go. The great information is that the output shaft on most gearboxes is fairly effortless to exchange. The poor information is… it is not often an isolated failure.
The 1st issue to do is to just take aside your gearbox and evaluate the complete extent of the injury. If it is truly just the output shaft, you must be in a position to modify it out, no dilemma. The output shafts start off at about $70 and go up in value depending on the measurement of the gearbox.
Nevertheless, in most cases, the bearings ($twenty/ea), seals ($ten/ea) and gear-established ($70) will also normally take a beating. If you’re unfortunate, the output cap ($eighty) will also undergo some harm.
In this circumstance, it is generally more affordable to exchange the gearbox. Evaluate the price tag of elements to the expense of an entire, new, warrantied gearbox. Often, even pros have to know when to get in touch with it a day.
I Want to Change my Input Shaft:
If you are drained of altering shear pins or searching back again and observing that your mower has not been chopping, you might want to set up 
a slip-clutch pto shaft (Indeed, we offer individuals too).
This typically calls for installing a 540-design, six-spline input shaft ($eighty five) on your mower’s gearbox.
Lucky for you, we did a write-up on our blog. It’s named “How to adjust the enter shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all audio variety-of equivalent over-the-phone. The best thing to do is to disassemble your gearbox and consider a seem at the gears and bearings. The concern will generally existing itself in the way of broken/lacking gear tooth, toasted gears (like that picture on our property page), or blown bearings.
If almost everything seems normal, try out altering the gear-mesh. This is accomplished with the mylar “gaskets” that sit between the major gearbox circumstance and the input/output caps. Consider adding or removing some of these spacers till your gears have approximately one/8″-one/four” of totally free engage in. Pros can purchase replacements ($one-2) in various thicknesses, but we recommend the swift and soiled approach of cutting your very own out of a sheet of mylar.
Never fail to remember to re-seal the gearbox with RTV right after you’ve discovered the right mixture. Even even though they are called “gaskets”, they won’t seal your gearbox on their possess.
Desire to know even more about Gearbox for Agricultural Machinery? See us 24/7 at http://hzpt.com/indgea.html.