helical bevel gear reducer

The EP Series Helical Bevel Reducer provides unmatched performance, durability, and style flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product collection of the entire gearbox and gear-engine system. Cat4CAD supports you in selecting and configuring these products, gives you the opportunity to print out comprehensive technical data sheets, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sizes.
Multiple Input Options: Integral gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, mounting pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For maximum rigidity, universal mounting on five sides or via a torque arm.
Worldwide Engine: Multiple leads and windings for worldwide multi volt/Hz requirements plus modular design to accept brakes, encoders or pressured cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft electric motor connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, encounter and flanged configurations. Gearmotors are available in three stage high efficiency designs through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft options. Additionally, you will find fixed and variable rate motors and selection of ratios obtainable in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Important dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and helical bevel gear reducer Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying demands of customers, you can expect a wide variety of Helical Bevel Equipment Reducers. The technological content material of our products allows for an extraordinary performance/lifespan ratio. The highly versatile Helical Bevel Gear Reducers we offer are successfully used in a vast number of industrial and civil applications. They are B-Series units that offer excellent value for money and result torque/weight ratio, especially considering that they need very limited servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with small motor, PB-fitted for engine coupling with flexible joint
Casing with ft FC, flange SC and general UC
Switch on to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 decrease stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second reduction stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM analysis and input and result flanges of grey cast-iron G200 to ensure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover package, viton oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel equipment motors provide ratios from 8:1 to 160:1 in three stages or up to 10000:1 in five phases. Motors are available up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and can be offered with single or double extended output shafts.
Products are also available as shaft mounted or with result flanges and are available for installation horizontally or vertically. The devices can also be provided with a bolt on torque reaction bracket and all variants can be found either motorised or with an input shaft assembly.
Adding to the new range of Ever-Power helical equipment motors the product takes benefit of our a long time of accumulated design knowledge together with the use of top quality materials and elements. The end result is a number of rate reducing geared motors providing high load having capacities, increased efficiency, tranquil running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double essential oil seals, on input and output shaft as required.
All products are dimensionally interchangeable with various other major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Units can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemicals, pharma, packaging, food processing, plastic material and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Power up to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series electric motor, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy components, specially and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, nice appearance ,and strong capacity to be overloaded.
6: Precise division and wide selection for transmission ratio.
7: The efficiency is up to as high because 96% with low energy intake, strong adaptability and is with the capacity of working continually in corrosive or damp environment.
8: All- purpose use, convenient and low-price maintenance.
9: New seal device, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.